<div class="phx-topic abstract-wrapper">US resin exports continued to grow strongly in 2020 and shippers say exports could have been even higher if it were not for rising domestic demand and production problems.</div>

US resin exports continued to grow strongly in 2020 and shippers say exports could have been even higher if it were not for rising domestic demand and production problems.

3676276_FI.jpg

<div>(The following story appears in the Top 100 US Importers and Exporters issue of The Journal of Commerce print magazine.)Despite improving demand, US resin exporters say production outages, strong domestic demand, and tight ocean capacity will make it difficult to repeat the impressive 80 percent average growth the sector has seen over the last three years in 2021.Containerized exports of US-produced resins rose 42.7 percent to 436,589 TEU last year after spiking 116.2 percent in 2019 and 81.5 percent in 2018, according to data from PIERS, a sister company of JOC.com within IHS Markit. Resins, a primary component in a...

(The following story appears in the Top 100 US Importers and Exporters issue of The Journal of Commerce print magazine.) Despite improving demand, US resin exporters say production outages, strong domestic demand, and tight ocean capacity will make it difficult to repeat the impressive 80 percent average growth the sector has seen over the last three years in 2021. Containerized exports of US-produced resins rose 42.7 percent to 436,589 TEU last year after spiking 116.2 percent in 2019 and 81.5 percent in 2018, according to data from PIERS, a sister company of JOC.com within IHS Markit. Resins, a primary component in a wide variety of plastic products, accounted for 22 percent of total US chemical exports last year, which grew 9.9 percent overall. Stephen Paul, vice president of supply chain management at Ray-Mont Logistics, said the company’s two resin packaging facilities, one of which opened last year, were at or near full capacity throughout 2020 thanks to exporters looking to reach overseas markets. The amount of resin the company is shipping so far in 2021 pales in comparison, Paul said. Ray-Mont went from handling between 200 and 240 railcars per week of bulk resin last year down to about 50 railcars this year, he said. “2020 was pretty strong for us on the resin side,” Paul said. “We saw demand increase significantly. But what we have seen in 2021 is that the numbers have dropped off dramatically.” US resin exports for the first quarter of 2021 were up 9.1 percent from a year earlier when COVID-19 first hit, according to PIERS. But that was a steep slowdown from the respective 52 percent and 23 percent year-over-year growth recorded in the third and fourth quarters of 2020. Weather disruptions crimp supply Paul said US resin producers began facing production shortfalls by the back half of 2020 owing to last year’s storm season, which produced four hurricanes that made landfall on the US Gulf Coast, the primary production and export region for resins. Led by Houston, which alone handled 77.8 percent of all resin exports from the US, Gulf Coast ports accounted for 88.4 percent of resin exports and 47.4 percent of the 1.94 million TEU of total chemicals exported in 2020. Click to enlarge After the storms, inventories of resins at US manufacturers sat at a non-seasonally adjusted $10.664 billion last October, the lowest levels since 2017, according to US Census Bureau data. “The hurricane season last year in the Gulf was the first supply chain disruptor,” Paul said. “It basically created a situation where they were a little bit behind.” At the same time, US domestic demand for resin began to shoot up thanks to COVID-19. Domestic manufacturers were looking to supply a surge in demand for plastic takeout containers and medical supplies because of the pandemic. With domestic prices increasing, resin traders and marketers diverted more product away from overseas markets, Paul said. “Gulf Coast production was more tempered at the end of 2020,” Paul said. “Then they had to divert more supply to meet domestic demand driven by medical products and the shift to more consumer demand.” With inventories already low going into 2021, US resin production took another hit from a February deep freeze in Texas. The resulting power outages knocked out about half of the volumes that US resin producers typically send to export markets, Paul said. “It just crippled production,” Paul said. “With what happened in Texas, that was the icing on the cake that pushed more supply into the North American market.” In the wake of the freeze, US resin exports fell to 32,413 TEU in February from 43,263 TEU in January, according to PIERS. March saw a slight gain in export volumes to 37,854 TEU. Terry Glass, executive director for plastics at IHS Markit, parent company of JOC.com, said Gulf Coast resin producers are on a path to recovering lost output. Resin plant utilization, which dropped to around 50 percent in the wake of the Texas deep freeze, reached 76 percent in March, Glass said. He expects utilization to reach 85 percent in April and a potential full recovery in production by the end of May. Glass said some resin is being sold in the spot market and for export, which indicates that more supply is becoming available. However, more volume will not be available until inventories have been built back up. “There are still issues with shortages,” Glass said. “Inventories are rebounding, but the inventory quality isn’t what it would normally be because of these short cycles.” According to Glass, the US resin inventory shortfall is so severe that the Department of Defense has ordered one of its contractors to prioritize plastics products for the military above other customers. US resin producers are also trying to push through price hikes for May and June in response to the shortfall, he said. There are some positive catalysts for US domestic production capacity. An ExxonMobil and Saudi Aramco joint venture resin plant in Corpus Christi may start up in July, ahead of an expected fourth-quarter 2021 opening, and Formosa Petrochemical is also restarting several resin production lines that were impacted by the deep freeze, Glass said. However, a recent fire at a Braskem plant in Mexico and production issues at a Nova Chemicals plant in Canada may steer more resin away from containerized export markets, Glass said. Resin prices in China have also been falling recently, further impacting export markets, he added. Paul said the high costs of ocean freight will also play a role in the ability of resin exports to rebound, adding that finding export containers and chassis is a growing challenge for resin shippers. While Houston is the main gateway for US resin exports, equipment availability is one of the reasons that Ray-Mont chose to locate its new packaging facilities near the ports of Charleston and Mobile, he added. Both sites are expected to open in 2022. “Despite what’s been happening, our customers told us we are on the right track,” Paul said. “Supply is going to rebound.” Contact Michael Angell at michael.angell@ihsmarkit.com and follow him on Twitter: @michael_angell .

Supply chain

Top US Shippers: Production woes, domestic demand dampen US resins exports

<div class="phx-topic abstract-wrapper">The journey time, about two to three days better than typical industry metrics, comes despite congestion in other parts of partner CPKC’s network.</div>

The journey time, about two to three days better than typical industry metrics, comes despite congestion in other parts of partner CPKC’s network.

Feature image

<div class="phx-topic">Schneider National said Friday its flagship Mexico Midwest Express (MMX) intermodal service with partner Canadian Pacific Kansas City (CPKC) is continuing to deliver strong results in 2025, offering faster transit times and higher on-time reliability than many cross-border alternatives despite congestion in other parts of CPKC’s network. The MMX service, launched two years ago, connects inland Mexican cities such as Monterrey and San Luis Potosí with Chicago via a single-line rail route. The service bypasses traditional interchange delays at the border, with two spans over the Laredo bridge and switching yards on each side of the border to handle crew changes. While Schneider did not disclose current shipment totals due to its quiet period ahead of the release of its second-quarter earnings, the company said MMX performance metrics through the first half of 2025 were strong, with average transit times of four days and a cargo theft rate of less than 0.02%. Schneider also said the on-time performance of MMX remains above 95%. The typical transit time from Monterrey to Chicago is about six or seven days. “Decreasing shipping time by even a few days matters to our customers because the faster products can get on the shelves, the faster those items can land in the hands of consumers,” Michael Baumgardt, Schneider’s senior vice president of intermodal, said in a statement. The Intermodal Association of North America (IANA) reported that railroads hauled a combined 86,000-plus domestic containers this year through May 31, a 21% increase compared with the same period a year earlier. Railroads hauled nearly 60,000 domestic containers to the Midwest during the same period, up 9% from a year earlier. Schneider is currently the only intermodal provider offering a true single-line cross-border solution from Mexico to the Midwest, eliminating any chance of delays caused by an interchange between two railroads. Schneider said service on the MMX has not deteriorated much since CPKC’s <a href="https://www.joc.com/article/cpkc-acknowledges-service-woes-to-us-regulators-vows-remediation-6030412">messy IT transition</a> in May that affected service in Texas, Louisiana, and Mississippi. The exception is that some shippers have experienced lengthy delays moving cargo from Laredo to Chicago because the container dwell inside the Laredo yard is up 122% since early May compared with a year ago. Schneider rivals <a href="https://www.joc.com/article/jb-hunt-launching-quantum-de-mexico-for-time-sensitive-cross-border-freight-6014579">J.B. Hunt Transport Services</a> and <a href="https://www.joc.com/article/hub-group-boosts-cross-border-business-in-jv-with-mexican-dray-carrier-5745355">Hub Group</a> have also ramped up investments in cross-border intermodal in recent months, introducing new services and partnerships aimed at capturing a growing share of freight moving between the US and Mexico. Union Pacific Railroad completed a pilot program this spring to speed up the handoff between Mexican and US crews by doing it inside UP’s Eagle Pass terminal rather than on the middle of the International Railway Bridge. Contact Ari Ashe at <a href="mailto:ari.ashe@spglobal.com">ari.ashe@spglobal.com</a>.</div>

Schneider National said Friday its flagship Mexico Midwest Express (MMX) intermodal service with partner Canadian Pacific Kansas City (CPKC) is continuing to deliver strong results in 2025, offering faster transit times and higher on-time reliability than many cross-border alternatives despite congestion in other parts of CPKC’s network. The MMX service, launched two years ago, connects inland Mexican cities such as Monterrey and San Luis Potosí with Chicago via a single-line rail route. The service bypasses traditional interchange delays at the border, with two spans over the Laredo bridge and switching yards on each side of the border to handle crew changes. While Schneider did not disclose current shipment totals due to its quiet period ahead of the release of its second-quarter earnings, the company said MMX performance metrics through the first half of 2025 were strong, with average transit times of four days and a cargo theft rate of less than 0.02%. Schneider also said the on-time performance of MMX remains above 95%. The typical transit time from Monterrey to Chicago is about six or seven days. “Decreasing shipping time by even a few days matters to our customers because the faster products can get on the shelves, the faster those items can land in the hands of consumers,” Michael Baumgardt, Schneider’s senior vice president of intermodal, said in a statement. The Intermodal Association of North America (IANA) reported that railroads hauled a combined 86,000-plus domestic containers this year through May 31, a 21% increase compared with the same period a year earlier. Railroads hauled nearly 60,000 domestic containers to the Midwest during the same period, up 9% from a year earlier. Schneider is currently the only intermodal provider offering a true single-line cross-border solution from Mexico to the Midwest, eliminating any chance of delays caused by an interchange between two railroads. Schneider said service on the MMX has not deteriorated much since CPKC’s messy IT transition in May that affected service in Texas, Louisiana, and Mississippi. The exception is that some shippers have experienced lengthy delays moving cargo from Laredo to Chicago because the container dwell inside the Laredo yard is up 122% since early May compared with a year ago. Schneider rivals J.B. Hunt Transport Services and Hub Group have also ramped up investments in cross-border intermodal in recent months, introducing new services and partnerships aimed at capturing a growing share of freight moving between the US and Mexico. Union Pacific Railroad completed a pilot program this spring to speed up the handoff between Mexican and US crews by doing it inside UP’s Eagle Pass terminal rather than on the middle of the International Railway Bridge. Contact Ari Ashe at ari.ashe@spglobal.com .

North-American rail

Intermodal providers

Schneider says MMX service delivering four-day Mexico-Chicago transit time

<div class="phx-topic abstract-wrapper">The project, due to begin Monday, will also improve truck access by upgrading the gate infrastructure and boost efficiency through the replacement of an outdated terminal operating system.</div>

The project, due to begin Monday, will also improve truck access by upgrading the gate infrastructure and boost efficiency through the replacement of an outdated terminal operating system.

<div class="phx-topic">The International Transportation Service (ITS) terminal in Long Beach will begin a $365 million upgrade on Monday that will increase its container capacity by about 50% and enable it to work two 18,000-TEU ships simultaneously. The work involves filling in a 19-acre slip at the terminal to make the property usable. Scheduled for completion in about three and a half years, the project will also improve truck access by upgrading the gate infrastructure and boost efficiency through the replacement of an outdated terminal operating system (TOS) with a new TOS, ITS CEO Kim Holtermand told the Journal of Commerce. “Our tech is quite old. It’s time to upgrade it,” Holtermand said. ITS is, in effect, two separate terminals separated by the slip, which hinders operational efficiency, Holtermand said. Filling in the slip will increase the terminal’s size to 277 acres and create a more efficient square-shaped facility. With a total of 3,500 linear feet of berth, ITS will be able to handle two super-post-Panamax container ships, or one 18,000-TEU vessel and two smaller ships simultaneously, he said. “It will be a large efficient facility with big [super post-Panamax] cranes and improved infrastructure,” Holtermand said. ITS’ annual throughput capacity will increase by about 50% to 1.5 million container moves, or 2.6 million TEUs, he said. <h3>Gate improvements expected to boost efficiency </h3>Included in the project will be a reconfiguration of the terminal’s gate complex and a new TOS that will streamline truck access and egress. Trucks calling at ITS in June had an average turn time of 71 minutes; the average turn time for the Long Beach-Los Angeles port complex in June was 62 minutes, according to the Harbor Trucking Association. ITS will also continue its efforts to electrify all its cargo-handling equipment by 2030 to meet the deadline set in the joint Los Angeles-Long Beach <a href="https://www.joc.com/article/la-lb-port-significantly-cuts-emissions-but-tougher-challenges-await-5742585">Clean Air Action Plan</a>, Holtermand said. The equipment will continue to be operated by dockworkers, he added. Noel Hacegaba, COO at the Port of Long Beach, said the ITS expansion project is the latest example of how the port and its stakeholders are not only growing, but growing green. Another project that will accomplish the port’s environmental goals is the <a href="https://www.joc.com/article/southern-california-ports-ready-to-defend-green-initiatives-from-trump-white-house-5927353">Pier B on-dock railyard</a> that will eliminate hundreds of truck trips each day by loading inland point intermodal (IPI) containers directly onto trains rather than trucking them to near-dock railyards, Hacegaba said. Construction of the Pier B facility continues to advance, he said, with completion expected in 2032. On-dock moves account for about 27% of Long Beach’s IPI volume; completion of the Pier B facility will raise that to about 35%, Hacegaba said. Contact Bill Mongelluzzo at <a href="mailto:bill.mongelluzzo@spglobal.com">bill.mongelluzzo@spglobal.com</a>.</div>

The International Transportation Service (ITS) terminal in Long Beach will begin a $365 million upgrade on Monday that will increase its container capacity by about 50% and enable it to work two 18,000-TEU ships simultaneously. The work involves filling in a 19-acre slip at the terminal to make the property usable. Scheduled for completion in about three and a half years, the project will also improve truck access by upgrading the gate infrastructure and boost efficiency through the replacement of an outdated terminal operating system (TOS) with a new TOS, ITS CEO Kim Holtermand told the Journal of Commerce. “Our tech is quite old. It’s time to upgrade it,” Holtermand said. ITS is, in effect, two separate terminals separated by the slip, which hinders operational efficiency, Holtermand said. Filling in the slip will increase the terminal’s size to 277 acres and create a more efficient square-shaped facility. With a total of 3,500 linear feet of berth, ITS will be able to handle two super-post-Panamax container ships, or one 18,000-TEU vessel and two smaller ships simultaneously, he said. “It will be a large efficient facility with big [super post-Panamax] cranes and improved infrastructure,” Holtermand said. ITS’ annual throughput capacity will increase by about 50% to 1.5 million container moves, or 2.6 million TEUs, he said. Gate improvements expected to boost efficiency Included in the project will be a reconfiguration of the terminal’s gate complex and a new TOS that will streamline truck access and egress. Trucks calling at ITS in June had an average turn time of 71 minutes; the average turn time for the Long Beach-Los Angeles port complex in June was 62 minutes, according to the Harbor Trucking Association. ITS will also continue its efforts to electrify all its cargo-handling equipment by 2030 to meet the deadline set in the joint Los Angeles-Long Beach Clean Air Action Plan , Holtermand said. The equipment will continue to be operated by dockworkers, he added. Noel Hacegaba, COO at the Port of Long Beach, said the ITS expansion project is the latest example of how the port and its stakeholders are not only growing, but growing green. Another project that will accomplish the port’s environmental goals is the Pier B on-dock railyard that will eliminate hundreds of truck trips each day by loading inland point intermodal (IPI) containers directly onto trains rather than trucking them to near-dock railyards, Hacegaba said. Construction of the Pier B facility continues to advance, he said, with completion expected in 2032. On-dock moves account for about 27% of Long Beach’s IPI volume; completion of the Pier B facility will raise that to about 35%, Hacegaba said. Contact Bill Mongelluzzo at bill.mongelluzzo@spglobal.com .

Container Shipping News

Port News

North American ports

Marine terminals

Maritime

Long Beach ITS terminal upgrade to boost capacity by about 50%

<div class="phx-topic abstract-wrapper">The decline came despite a 4.4% increase in total container volumes to 2 million TEUs, the carrier said in a quarterly update Friday.</div>

The decline came despite a 4.4% increase in total container volumes to 2 million TEUs, the carrier said in a quarterly update Friday.

<div class="phx-topic">OOCL’s second-quarter revenues dropped 6.5% year over year to $2.1 billion amid falling freight rates on trans-Pacific and Asia-Europe services, the carrier said in a quarterly update Friday. The revenue decline came despite a 4.4% increase in total container volumes to 2 million TEUs, the carrier said. OOCL, the liner offshoot of Hong Kong-listed Orient Overseas (International), a Cosco Shipping Holdings subsidiary, said second-quarter trans-Pacific revenues were also hit by a 4.3% fall in container volumes to 501,814 TEUs. Trans-Pacific revenues fell 18% to $753 million in the second quarter from $922 million a year earlier. OOCL said revenue from Asia-Europe services dropped 15% to $443 million in the April–June period despite a 3% increase in liftings to 361,722 TEUs. There were brighter results in OOCL’s two other main markets. Intra-Asia and Australasia remained OOCL’s biggest contributor to revenue and volumes after the carrier saw a 9% increase to $728 million in second-quarter revenue. Liftings climbed 8% to 951,940 TEUs. Revenue from trans-Atlantic services surged 25% to $194 million, while container volumes rose 21% to 147,824 TEUs. OOCL’s update only gave revenue and liftings figures; parent company OOIL will likely release full half-year results in mid-August. The carrier’s revenue result echoes that of Taiwan’s Big Three container lines, <a href="https://www.joc.com/article/taiwans-big-three-carriers-see-falling-q2-revenues-as-demand-slump-begins-6041608">which on Wednesday reported worsening second-quarter revenues</a> compared with the first quarter. Contact Keith Wallis at <a href="mailto:keithwallis@hotmail.com">keithwallis@hotmail.com</a>.</div>

OOCL’s second-quarter revenues dropped 6.5% year over year to $2.1 billion amid falling freight rates on trans-Pacific and Asia-Europe services, the carrier said in a quarterly update Friday. The revenue decline came despite a 4.4% increase in total container volumes to 2 million TEUs, the carrier said. OOCL, the liner offshoot of Hong Kong-listed Orient Overseas (International), a Cosco Shipping Holdings subsidiary, said second-quarter trans-Pacific revenues were also hit by a 4.3% fall in container volumes to 501,814 TEUs. Trans-Pacific revenues fell 18% to $753 million in the second quarter from $922 million a year earlier. OOCL said revenue from Asia-Europe services dropped 15% to $443 million in the April–June period despite a 3% increase in liftings to 361,722 TEUs. There were brighter results in OOCL’s two other main markets. Intra-Asia and Australasia remained OOCL’s biggest contributor to revenue and volumes after the carrier saw a 9% increase to $728 million in second-quarter revenue. Liftings climbed 8% to 951,940 TEUs. Revenue from trans-Atlantic services surged 25% to $194 million, while container volumes rose 21% to 147,824 TEUs. OOCL’s update only gave revenue and liftings figures; parent company OOIL will likely release full half-year results in mid-August. The carrier’s revenue result echoes that of Taiwan’s Big Three container lines, which on Wednesday reported worsening second-quarter revenues compared with the first quarter. Contact Keith Wallis at keithwallis@hotmail.com .

Container lines

Trans-Atlantic

Asia-Europe

Trans-Pacific

OOCL’s Q2 revenue slides on lower trans-Pacific, Asia-Europe rates

<div class="phx-topic abstract-wrapper">Adoption of digital bills of lading has been stronger in Asia, but US traction is necessary to help container lines meet a 2030 commitment to fully move to electronic documents.</div>

Adoption of digital bills of lading has been stronger in Asia, but US traction is necessary to help container lines meet a 2030 commitment to fully move to electronic documents.

<div class="phx-topic">US Bank has completed its first trade finance transaction using a digital ocean bill of lading (BoL), another small step toward the industry’s intent to transition to 100% digital BoLs by 2030. The transaction, disclosed by US Bank on Thursday, was facilitated by electronic bill of lading (eBL) software vendor WaveBL for a US-based exporter using Mediterranean Shipping Co., which issued the eBL. MSC is a WaveBL customer, one of two container lines using the software vendor; Zim Integrated Shipping Services is the other. Adoption of eBLs is growing, but off a low base, and is more commonly used in Asia, where the eBL software provider IQAX is getting traction among banks and export suppliers. The nine member carriers of the Digital Container Shipping Association (DCSA) committed in early 2023 to shift to 100% digital bills of lading by 2030. This week’s move by US Bank highlights the potential in American banks adopting a process to accommodate digital BoLs. Traditionally, bills of lading transfer titles between buyers and sellers at a point determined by the shipment’s Incoterm, and banks traditionally play a role in issuing letters of credit to suppliers. In theory, an eBL would negate the need for most letters of credit, as the digital data contained in the document can be used by the buyer, seller, shipping line and banks to understand the financial risk of the shipment. “Our clients are looking for smarter, more efficient ways to manage their import and export activities,” US Bank Senior Vice President Christine Bravo said in a statement. US Bank said a transaction such as this normally would require a courier to physically transport documents across continents, often taking several days. “By contrast, the digital process reduced that timeline to minutes, eliminating delays, [and] enhancing security and compliance,” the bank said. Contact Eric Johnson at <a href="mailto:eric.johnson@spglobal.com">eric.johnson@spglobal.com</a>. </div>

US Bank has completed its first trade finance transaction using a digital ocean bill of lading (BoL), another small step toward the industry’s intent to transition to 100% digital BoLs by 2030. The transaction, disclosed by US Bank on Thursday, was facilitated by electronic bill of lading (eBL) software vendor WaveBL for a US-based exporter using Mediterranean Shipping Co., which issued the eBL. MSC is a WaveBL customer, one of two container lines using the software vendor; Zim Integrated Shipping Services is the other. Adoption of eBLs is growing, but off a low base, and is more commonly used in Asia, where the eBL software provider IQAX is getting traction among banks and export suppliers. The nine member carriers of the Digital Container Shipping Association (DCSA) committed in early 2023 to shift to 100% digital bills of lading by 2030. This week’s move by US Bank highlights the potential in American banks adopting a process to accommodate digital BoLs. Traditionally, bills of lading transfer titles between buyers and sellers at a point determined by the shipment’s Incoterm, and banks traditionally play a role in issuing letters of credit to suppliers. In theory, an eBL would negate the need for most letters of credit, as the digital data contained in the document can be used by the buyer, seller, shipping line and banks to understand the financial risk of the shipment. “Our clients are looking for smarter, more efficient ways to manage their import and export activities,” US Bank Senior Vice President Christine Bravo said in a statement. US Bank said a transaction such as this normally would require a courier to physically transport documents across continents, often taking several days. “By contrast, the digital process reduced that timeline to minutes, eliminating delays, [and] enhancing security and compliance,” the bank said. Contact Eric Johnson at eric.johnson@spglobal.com .

Logistics Technology News

US Bank eBL trial for US exporter notches another step toward 2030 goal

<div class="phx-topic abstract-wrapper">The Marseille-based liner has finalized operational plans to call off its remaining vessel-sharing agreements with the carriers after Gemini Cooperation-linked realignments.</div>

The Marseille-based liner has finalized operational plans to call off its remaining vessel-sharing agreements with the carriers after Gemini Cooperation-linked realignments.

<div class="phx-topic">CMA CGM is switching from vessel-sharing agreements (VSAs) to standalone operations across trades out of India in a new strategic approach as it expands its fleet. The Marseille-based liner has finalized operational plans to call off its two remaining VSAs with Hapag-Lloyd and Maersk after Gemini Cooperation-linked realignments. The upcoming disengagements include the Swahili Express (SWAX2) loop run with Hapag-Lloyd on the India-East Africa trade and the Midas network, involving two strings, operated with Maersk on the India-West Africa trade. CMA CGM has had three ships out of the five used on the joint SWAX2, with one vessel each from Hapag-Lloyd and Emirates Shipping Line (ESL). Midas has involved a fleet of 10 ships — six from Maersk and four from CMA CGM — on String 1 and three vessels from each on String 2. The French carrier has already sent its partners termination notices, due to take effect from next month for the SWAX2 operation and from late 2025/early 2026 for the Midas network. Sources at Hapag-Lloyd and Maersk in India were unavailable for comment. The Gemini launch in February saw CMA CGM delink from the decades-long consortium partnerships with Hapag-Lloyd on the India-US East Coast and North Europe trades. CMA CGM’s India VSA operations are now confined to Cosco Shipping/OOCL on the Epic service. Contact Bency Mathew at <a href="mailto:bencyvmathew@gmail.com">bencyvmathew@gmail.com</a>. </div>

CMA CGM is switching from vessel-sharing agreements (VSAs) to standalone operations across trades out of India in a new strategic approach as it expands its fleet. The Marseille-based liner has finalized operational plans to call off its two remaining VSAs with Hapag-Lloyd and Maersk after Gemini Cooperation-linked realignments. The upcoming disengagements include the Swahili Express (SWAX2) loop run with Hapag-Lloyd on the India-East Africa trade and the Midas network, involving two strings, operated with Maersk on the India-West Africa trade. CMA CGM has had three ships out of the five used on the joint SWAX2, with one vessel each from Hapag-Lloyd and Emirates Shipping Line (ESL). Midas has involved a fleet of 10 ships — six from Maersk and four from CMA CGM — on String 1 and three vessels from each on String 2. The French carrier has already sent its partners termination notices, due to take effect from next month for the SWAX2 operation and from late 2025/early 2026 for the Midas network. Sources at Hapag-Lloyd and Maersk in India were unavailable for comment. The Gemini launch in February saw CMA CGM delink from the decades-long consortium partnerships with Hapag-Lloyd on the India-US East Coast and North Europe trades. CMA CGM’s India VSA operations are now confined to Cosco Shipping/OOCL on the Epic service. Contact Bency Mathew at bencyvmathew@gmail.com .

CMA CGM ends existing Indian VSAs with Hapag-Lloyd, Maersk

Use code SKSGW995 at checkout to save $500 on first year of a Gold subscription and 20% on a TPM26 registration!

Subscribe Now - FT/Anonymous to Gold - Wide Box

SUMMER SALE EXTENDED

Use code GTW695 at checkout and save $800 on first year of an annual Gold subscription!

Upgrade Subscription - Gold Trials

Become a Gold Subscriber and Save!

Use code SKSW595 at checkout to save $900 on first year of a Gold subscription and 20% on a TPM26 registration!

Upgrade Subscription - S/SP to Gold - Wide Box

Arm your team with the most trusted information portal for the international container shipping industry.

Group Subscriptions - Wide Box

Get into a group subscription today

Access Journal of Commerce content for 30 days

Free Trial - Wide Box

START A FREE TRIAL TODAY

Use code SkSW25 at checkout to save 25% on a SIlver or Silver Plus annual subscription! 

Subscribe Now - FT/Anonymous to S/SP - Wide Box

The world of LTL is slow to embrace change. Business anachronisms permeate current supply chain processes. These vestiges of the way things used to work define the LTL freight transportation procurement process of many modern shippers.David Knuth, logistics specialist at IEWC, a global supplier of cable and wire based in Wisconsin, is happy to have modernized the RFP process, automating the entire LTL bidding procedure with Bid$ense, SMC³’s automated truckload and LTL freight transportation sourcing solution. But when prompted, he can still recall what once was.In his previous job, a large part of his duties were consumed by creating an intermodal bid package for carriers. In a spreadsheet, Knuth detailed the company’s volumes lane by lane, taking care to delete any errant keystrokes or misleading data. He would then email out the information to each carrier, taking time to respond to detailed technical questions about the spreadsheet data. Finally, he had to compile all the results, create an algorithm that would compare the carriers on each lane, and award the business.“It was a huge undertaking. It took about four months to do,” Knuth said of the old process. “It was almost a full-time job for that part of the year, every year.”In his new job at IEWC, he sat down with Bid$ense on day one and was amazed at the capabilities. Knuth had never before used a bid tool. SMC³’s latest versions of Bid$ense automate the process even further, taking truckload and LTL RFPs entirely online. The tool draws on RFP best-practices protocols to streamline the bidding communication process, enabling bidding carriers to respond accurately and promptly to shipper requests. The solution also does all the distribution work automatically, electronically submitting shipper bid data to carriers based on their actual service capabilities and performance records. Carriers are alerted with timely prompts for RFP deliverables, so shippers aren’t waiting by the phone for responses.Another benefit of automating the process is the data-cleansing assistance. When Knuth sent spreadsheets to carriers, data errors might cloud the bidding process; he might have to resend data or simply accept a price that did not truly reflect the costs of doing business. Data cleansing is incredibly beneficial, he said.The spreadsheet technique also made bidding analysis an onerous task. Since Bid$ense automates and streamlines the entire RFP process, intensive examination is now simple. SMC³ knows that each bid has more than one best outcome. With uniform responses from each carrier, shippers can quickly rank results and create an unlimited quantity of what-if scenarios to make the optimal procurement decision.Jesse Burnett of Central Garden &amp; Pet experiences many of the same benefits. Founded in 1980, Central Garden &amp; Pet has spent the last three decades growing from a small garden supply company to a provider of a range of products from dog chews and bird seed to soil supplements and natural insecticides. For much of its life, the company shipped these disparate goods via LTL and truckload carriers to retailers throughout the country, relying on each business unit to negotiate directly with their freight transportation providers. This arrangement worked fairly well for a small company, but as Central Garden &amp; Pet expanded, leadership decided to consolidate decision making.Burnett helped centralize the transportation decision making in 2015 with SMC³’s Bid$ense. Before Bid$ense, every business unit operated independently as far as negotiating with carriers.“There were a lot of different things just floating around,” he said. “We didn’t have master agreements in place; no national pricing at all. The pricing from carriers was just all over the place, depending on where you were.”The transformations he saw with Bid$ense were immediate. Burnett has been using the tool about every other year since its implementation at the company. Central Garden and Pet’s $19.6 million 2019 LTL bid saved the company just more than 9 percent when compared to its historical average. For Burnett, though, bid automation extends far beyond savings.“We knew that we weren’t getting the best pricing offer from our carriers just because nothing was centralized,” he continued. “We knew that if we combined everything from all these business units and paired it with one corporate offering, then it would drive some cost benefit with it.”When the company initially decided to centralize bid procurement, executives researched a number of different methodologies and technologies. In the end, though, Burnett found that Bid$ense was both widespread and well known, and that his carrier partners already knew how to use the application. Burnett also highlighted the data-cleansing process as a major benefit, saying the rigorous process ensures that carriers always return the best price.“It definitely has helped drive savings,” he said. “Any time you go out there and you drive that competitiveness with the carriers and they know they’re in a bid environment, it seems to sharpen their pencils.”Transportation procurement is an integral part of the modern supply chain. With Bid$ense, shippers can develop a strategic implementation plan that saves them time and money, but also helps them create strong relationships with their carrier partners. These carriers appreciate the solution’s data-cleansing process; when carriers receive a complete shipment history and future volume forecast, they don’t have to guess on pricing. Carriers that receive more data from shippers get a complete picture of that shipper’s freight, allowing them to accurately plan instead of simply preparing for the worst-case scenario. Clean data presented through an automated system can lead to both bigger shipment savings and a lasting partnership between carrier and customer.Whether customers are looking to streamline over-the-road transportation bidding by automating the RFP process or create an entirely new, centralized sourcing process, Bid$ense has the analytical horsepower to get the job done.SMC³ 2020 Customer Case Study

SMC3rates_shutterstock_5247046.jpg

Shippers save money, time with automated transportation bidding tools

If there’s one immutable truth in the world of logistics, it’s this: LTL is an inherently complex form of transportation. Tariffs, rates, DIM weights, transit times — it’s enough to confuse even seasoned logistics professionals. The solution to this knowledge gap has historically been on-the-job training or university supply chain education, but for a variety of reasons there is now a pressing need for third-party, remote LTL training that prepares logistics workers for transportation success. Global Scope Can Overlook Local Intricacies In the past, professionals looking to move into a supply chain career learned about the basics of supply chain from universities. However, many of these college supply chain programs are now global in scope, focusing on worldwide supply chain management instead of the intricacies of specialized domestic transportation. And even these programs, which used to be widespread, are becoming less common. LTL is not an industry of broad-brush strokes; supply chain professionals really need a pointillistic understanding of the logistics of LTL in order to excel in the industry. Accelerating Need for Dedicated LTL Education This lack of specified training put the onus on employers to prepare new hires with the LTL knowledge needed to do their jobs. Dedicated LTL study is a necessity, not a luxury. At the same time, changes in LTL and the broader supply chain world are accelerating. The reliance on e-commerce has ballooned since the start of the pandemic, and last-mile LTL shipments and related e-commerce strains on the supply chain won’t diminish once social distancing abates. That genie isn’t going back into the bottle. So supply chain employers need logistics workers that are fully versed in all aspects of the industry, ready to solve unique shipping and delivery problems based on their extensive supply chain knowledge But why care about LTL? It’s been reported that some shippers in today’s world are no longer concerned with what mode is used to ship their goods. A Multimodal Approach Ensures On-Time Delivery This mode agnosticism means supply chain stakeholders have to be well versed in all modes of transportation. As unforeseen weather events and other disruptions, such as protests, become more common, savvy logistics employees will need to be armed with familiarity of all modes, not just the most popular, to ensure that freight is delivered on time, without damage, and in the most financially expedient way possible. Offerings like SMC³’s LTL online education courses cover a wide range of topics from LTL basics and operations to more advanced concepts like pricing analytics and transportation law. The company also has plans to continually refresh content, adding new expert presenters and taking the feedback of students to make the courses even better as time goes on. Learn more about&nbsp;<a href="https://logisticstrainingcenter.com/smc3-courses/" rel="noreferrer" class="joc_admin__link">SMC³’s LTL Online Education program</a>&nbsp;and view the 2021 hybrid schedule, featuring live industry experts,&nbsp;<a href="https://www.smc3.com/onlinelearning2021/" rel="noreferrer" class="joc_admin__link">here.</a>

SMC3rates_shutterstock_5247046 (1).jpg

Filling the Supply Chain Education Gap with LTL Education Courses

SUMMER SALE EXTENDED: Use code SKSGW995 to save $500 on an annual Gold subscription and 20% on a TPM26 registration!

Subscribe Now - FT/Anonymous to Gold - Offer Box

SUBSCRIBE AND SAVE

UPGRADE TO GOLD AND SAVE: Use code GTW695 at checkout and save $800 on first year of a Gold subscription!

Upgrade Subscription

SUMMER SALE EXTENDED: Use code SKSW25 to save 25% on first year of a Silver or Silver Plus annual subscription!


Subscribe Now - FT/Anonymous to S/SP - Offer Box

GET INTO A GROUP SUBSCRIPTION: Arm your team with unlimited Journal of Commerce content

Group Subscriptions - Offer Box

Group Subscriptions

SUMMER SALE EXTENDED: Use code SKSW595 at checkout to save $900 on first year of a Gold subscription and 20% on TPM26! 

Upgrade Subscription - S/SP to Gold - Offer Box

START A FREE TRIAL: Access Journal of Commerce content for 30 days

Free Trial - Offer Box

Free Trial

Monthly publication providing an editorial deep dive into global supply chain news

Journal of Commerce Magazine - Rectangle Box

Journal of Commerce Magazine

An in-depth analysis of transport trends in the multipurpose and heavy-lift fleet segment

Breakbulk Report - Rectangle Box

Breakbulk Quarterly

Customers scoring their intermodal partners to identify the best service providers

Intermodal Service Scorecard - Rectangle Box

Intermodal Service Scorecard

A must-attend conference for shippers & logistics providers moving goods inland

Inland Conference - Rectangle Box

Attend Inland25

A premium access index of savings using domestic intermodal vs. OTR 

ISI Report - Rectangle Box

Intermodal Savings Index

An extensive dashboard of charts organized by trade lane, mode, and topic

Gateway - Rectangle Box

Gateway

A premium access outlook critical to shippers and transportation providers

QI Report - Rectangle Box

Quarterly Intelligence

The Journal of Commerce’s supply chain news and analysis impacting the management of end-to-end supply chains reports on supply chain strategies, cargo visibility, inventory trends, sourcing, customs certification and contract logistics. Supply chain news coverage also delves into refrigerated shipping advancements and management of inventory status, regulatory updates and government funding projects.

Stay informed with the latest regulation news and trade updates. Explore comprehensive transportation news and trade regulations today.

Transport, Trade and Regulation News | Journal of Commerce

Transport, Trade and Regulation News

Our logistics technology news include logistics technology startups, solutions, and the impact of technology on logistics and supply chain management.

Logistics Technology News | Journal of Commerce

A thorough cool cargoes news by Journal of Commerce. Learn about the latest trends in refrigerated cargo transportation, weight capacity, technology, and more.

Cool Cargo News | Journal of Commerce

Cool Cargo News

Journal of Commerce keeps you informed on the latest last mile news with comprehensive coverage of carriers, logistics, and last mile transportation solutions.

Last Mile News | Journal of Commerce

Last Mile News

Discover the latest industrial real estate news and trends. Covering projects, real estate supply chain, logistics, pricing, cross dock facilities, and more.

Industrial Real Estate News | Journal of Commerce

Industrial Real Estate News

Stay updated on supply chain strategies, cargo visibility, inventory trends and more with our comprehensive supply chain news and analysis.

Latest News

More News & Analysis

Schneider says MMX service delivering four-day Mexico-Chicago transit time

Long Beach ITS terminal upgrade to boost capacity by about 50%

OOCL’s Q2 revenue slides on lower trans-Pacific, Asia-Europe rates